Menu
en-USfr-FRde-DEit-ITes-ES


RESINOID CUP
FOR GRINDING
WITH AN ANGLE GRINDER

a picture of an angle grinder grinding with a resinoid cup

   
a vertical grinder a drawing of someone grinding safely with a vertical grinder a resinoid cup wheel of maximum 180 millimeters diameter

 
These products are referred to as resinoid cup wheels or straight and taper cup wheels.

These wheels improperly used can be dangerous: They run at up to 80 m/s on angle grinders and can eject parts at a speed of 288 km/h (180 mph) in case of breakage. FEPA has designed this page to provide the essential safety recommendations for use of diamond dish/cup wheels on angle grinders, with maximum diameter of 180mm.

Abrasive products

 
These recommendations focus on resinoid cup wheels for grinding with angle grinders. They may also be used on vertical grinders. They may have a plain bore or threaded bore. For speeds up to 63m/s a plain or claw insert is used, and for 80m/s a full safety back is used as shown below.

a vertical grinder with a resinoid cup wheel on each side        4 resinoid cup wheels shaped differently        2 resinoid cup and inserted nut disc wheels

Safety recommendations for the use resinoid cup wheels for grinding with angle grinders

80% of the accidents with abrasive products are due to its misuse or mishandling. This website has been created by FEPA's experts to spare the end-users from getting hurt while using abrasive products professionally or for home projects.

FEPA general safety principles

cover page of the safety recommendations leaflet for the use of abrasives products

Dos & Don’ts for these products

 
Soon available

 

 

 

 

 

 

 

 

 

What is a safe product? What should I look for?

 
FEPA recommends that only resinoid cup wheels conforming to EN 12413 and marked as such should be used.

Resinoid cup wheels not bearing EN 12413 may not conform the highest safety standards.

Before selecting the wheels, ensure that the expiry date has not been exceeded. 

All wheels should be examined carefully for damage or defects before fitting on the machine.
  

How should I handle and store the wheels?

 
All resinoid cup wheels are fragile. They should be handled with care. 

Wheels should be stored on a flat, rigid surface, avoiding damp and frost or wide variation in temperature.

Use the oldest wheels (on “first in, first out” basis).

 

 

 

 

How should I fit the wheel on the machine?

 
Follow carefully the instructions given in the machine handbook. 

Tighten only by hand.

Keep screw threads clean and free of burrs and rust.

Run all wheels after fitting for at least 30 seconds at operating speed keeping behind the guard in case the wheel breaks.

Refer to the FEPA recommended mounting check list.
 

 

How should I protect myself?

 
FEPA recommends the use of following personal protective equipment (often written PPE): 

Eye protection
Ear protection (ear sets)
Hand protection (gloves)
Lung protection (dust mask, also called respirator)

Never remove the protective machine guard and make sure it is properly adjusted to deflect debris away from you.

Ensure that no other person is at risk, especially near the machine while working.

How should I handle the wheel after use?

 
Before storing the machine or transporting it to another location, always remove the wheel and store it as recommended. 

Always carefully examine the wheel for damage or defects, and destroy and discard if damaged. 

When disposing of worn out or defective wheels, it is recommended to damage them to prevent someone from removing them from waste and re-using them. 

 

 

 

 
 

 

How can I get proper training?

 
It is a legal requirement for all employees involved in the use of abrasives wheels to be properly trained and also re-trained on a regular basis. They should consult their employer if they have not received this training.

The wheel manufacturer or supplier can advise you on suitable accredited training providers. 

As a private consumer, you should read carefully the safety information found in: 

 The grinding machine handbook
 FEPA general safety principles leaflet (see above)
 The FEPA safety leaflet for this specific application (soon available)

 

illustration of how to grind with a resinoid cup on an angle grinder


This website is intended to give information on safe use of abrasives in compliance with European standards, and not to give advice on product selection.
You should read the information given on the product or its packaging to determine suitability. For any specific question, contact the retailor who supplied you the product.